If you are after the best fridge slides for truck beds, the honest answer is that the MORryde SP56-115 leads the pack for most people. It carries a 225 lb load rating, runs on 200 percent extension ball-bearing slides, and weighs 68 lb, which is a lot to put in a half-ton bed. The ARB and Dometic slides are the better call if you already own a fridge from one of those brands.
What a fridge slide actually is: a steel tray on ball-bearing runners that bolts to your bed floor, a Goose Gear rear plate or a Front Runner drawer system, so the loaded fridge rolls out to the tailgate instead of living at the back of a packed bed. That one change decides whether cooking at the tailgate is a two-minute job or a five-minute scramble over your own firewood.
We spent weeks going through owner reviews on ten widely reviewed slides in this category, comparing load ratings, inner tray dimensions, extension length, mounting hardware and reported rattle. Two numbers decided most of the ranking: the published load rating against your fridge’s real loaded weight, and the inner tray width against your fridge footprint. If you are storing food correctly once the fridge is out, our guide to how long leftovers last in a fridge is worth a read too.
Table of Contents
Top 3 Best Fridge Slides for Truck Beds (October 2026)
MORryde SP56-115 Freezer Sliding Tray
- 225 lb weight capacity
- 200% extension slides
- Dual latches
- 68 lb unit weight
Rough Country 99021 Cooler Sliding Tray
- 250 lb weight capacity
- Ball-bearing slides
- Four cam-lock straps included
- 31.5 lb unit weight
SAMOUT SMFS-30 Fridge Slide
- 285 lb weight capacity
- Positive lock both positions
- Four buckle straps
- Three-year warranty
Quick Overview: Every Fridge Slide in This Roundup In 2026
Every slide below bolts down to a flat surface, and the differences come down to load rating, inner tray footprint, extension behaviour and how the fridge is retained. Read the load rating first, then the inner tray width, then everything else.
| Product | Specifications | Action |
|---|---|---|
| MORryde SP56-115 Freezer Sliding Tray |
|
Check Latest Price |
| Rough Country 99021 Cooler Sliding Tray |
|
Check Latest Price |
 ARB 10900021 37/50 Quart Fridge Slide |
|
Check Latest Price |
 ALL-TOP ATFS-30a Fridge Slide |
|
Check Latest Price |
| SAMOUT SMFS-30 Fridge Slide |
|
Check Latest Price |
 Dometic CFX3 50/55/65 Slide Mount Kit |
|
Check Latest Price |
 ARB 10900040 Elements 63QT Slide |
|
Check Latest Price |
 ICECO JP Pro Series Slide Mount |
|
Check Latest Price |
 ARB 10900048 Zero 63/73QT Slide |
|
Check Latest Price |
 SetPower Universal Refrigerator Slide Mount |
|
Check Latest Price |
Is a Fridge Slide Worth It?
Yes, for most truck campers, overlanders, hunters and tailgaters, and the payoff is access rather than capacity. A slide turns a fridge you have to climb into the bed for into one you reach from the tailgate, which is exactly the complaint that comes up again and again in overlanding forum threads.
Two cases where it is not worth it. In a short bed where the fridge can be lifted out easily anyway, a slide steals usable flat space. And if your setup is a slide-out camper or a van drawer, you probably need a different mounting method than a bed-mounted tray.
Budget for one honest surprise: the slide itself has weight before you ever load it. A 68 lb tray plus a loaded 50L fridge is a meaningful chunk of a half-ton payload, which is why we cover the payload math in detail further down.
1. MORryde SP56-115 Freezer Sliding Tray – Best Overall for Truck Beds
MORryde SP56-115 Freezer Sliding Tray 37.61″ W x 21.6″ D x 3.5″ H Front Pull
225 lb load rating
200% extension slides
Outer 37.6 x 21.6 x 3.5 in
Inner tray 31.42 x 19.7 in
Pros
- 225 lb load rating clears most portable fridges with room to spare
- 200% extension pulls the tray well clear of slide-outs and bed walls
- Dual latches hold the unit secure in transit
- Weighs 68 lb so plan your payload
- Installs in minutes with basic tools
Cons
- 31.42 in inner width will not fit the Dometic CFX3 95 DZ which needs 36 in
- Latches sometimes need slight adjustment to clear a fridge door gasket
The MORryde SP56-115 is the slide we kept coming back to while building this list. It is a 37.61 in wide by 21.6 in deep by 3.5 in tall steel tray with a 31.42 by 19.7 in inner tray, and it runs on runners that extend 200 percent of their closed length. That extension figure is the number that actually matters in a truck bed, because it gets the fridge out past the tailgate rather than just to the middle of the bed.
Owners consistently describe the construction as sturdy and the bearings as smooth even with a loaded fridge in the tray. The dual latches are there to hold the unit during travel, and the manufacturer rates the tray to 225 lb. That figure has real headroom: most mid-size portable fridges land well under it even with a full load of food and drinks.
The honest weakness is footprint. At 31.42 in of inner width, this tray will not accept the widest dual-zone units. A Dometic CFX3 95 DZ needs 36 in of width, and no amount of clever packing gets around that. Several owners also noted the latches needed a small adjustment so they would clear a fridge door gasket rather than pressing against it.
Check the Fridge Width Before You Order
Measure the widest point of your fridge, including any handle or latch housing, and compare it to the 31.42 in inner tray width. If your fridge is 30 in or narrower you are fine. Between 30 and 32 in it is tight, and above 32 in you need a wider tray or a different slide entirely.
Depth matters less because most owners run the fridge forward against the tray’s front stop. If you want a solid end stop against fore-aft movement, look for a tray with a lip or add your own strap across the front face.
Where the 68 lb Weight Matters
At 68 lb this is one of the heavier slides in the group, and that lands on your payload number before you add anything else. If you are running a lithium battery bank, a dual-zone fridge and a full camp kit, add the slide weight to the total and compare it against the payload figure on your door jamb sticker.
In return you get the 225 lb rating and the 200 percent extension, and that combination is hard to find elsewhere in a bolt-down bed tray. For a weekend tailgate rig or a build where weight is not the binding constraint, this is the one we would put in the bed.
2. Rough Country 99021 Cooler Sliding Tray – Best Value Steel Slide
Rough Country Cooler Sliding Tray for 45 L Portable Refrigerator/Freezer – 99021
Up to 250 lb weight capacity
31 x 19 x 2.5 in closed, 60.5 in extended
Inner tray 29.5 x 16.75 in
31.5 lb unit weight
Pros
- Up to 250 lb capacity from ball-bearing slides
- Mounting hardware nutserts and four cam-lock hold-down straps in the box
- Powder-coat finish resists chipping
- Secondary side lock holds the tray during travel
- Also works for toolboxes and generators
Cons
- Can squeak and rattle on washboard roads
- especially inside a wood enclosure
- Some buyers reported bent metal on the slide tracks on arrival
- Raises the fridge about 1 in above its normal position
The Rough Country 99021 is a 31 in long by 19 in wide by 2-1/2 in tall tray that extends to 60.5 in, with a 29.5 by 16.75 in interior. It is designed to pair with the Rough Country portable electric cooler, but owners use it for Engel, Dometic and other portable fridges of a similar footprint, and plenty of them never put a fridge in it at all.
What makes this the value pick is what arrives in the box. You get ball-bearing slides, mounting hardware, nutserts and four cam-lock hold-down straps, which means the retention system is solved for you on day one. Most competitors in this price band sell the tray and leave you to source your own straps.
Reviewers like the one-handed operation, the solid welds and a powder-coat finish that has held up for them. Several use it as a general cargo tray for toolboxes and generators, which is why the frame holds up under that kind of load.
The complaints are about noise and vibration rather than strength. On washboard and rutted roads the tray can squeak and rattle, especially inside a plywood camper enclosure where there is nothing to damp the resonance. A small number of buyers also received units with bent metal on the slide tracks, which is a packing problem rather than a design one.
Whether It Fits Your Fridge Footprint
At 29.5 in of inner length and 16.75 in of inner width, this is one of the tighter trays on the list. That is comfortable for 35L to 45L portable fridges and marginal for anything larger. Check your fridge’s depth against the 29.5 in inner dimension rather than the 31 in external figure, because the wall thickness eats into usable space.
Keep in mind the tray sits about 1 in higher than the fridge would on the bare bed floor. On a truck with a tonneau cover that extra inch is sometimes the difference between clearing and not clearing, so measure your closed height before you commit.
How It Behaves With a Bed Liner
The included nutserts and bolt pattern are the reason this works well with a bed liner in place. You can drill through a moulded mat, back it with the supplied hardware and get a solid fix without the tray rocking under a heavy fridge.
Watch for the rattle feedback as much as the load rating. If your truck lives on washboard roads, a strip of closed-cell foam between the tray frame and the bed floor is a cheap fix that takes an afternoon.
3. ARB 10900021 37/50 Quart Fridge Slide – Best for ARB Classic Fridges
ARB 10900021 37/50 Quart Fridge Freezer Slide Accesories
175 lb maximum weight capacity
Tray 26 x 16 in
Unit weight 27.6 lb
Epoxy or E-coat finish
Pros
- Smooth bearings that stay smooth when fully loaded
- Turns a hard-to-reach mounted fridge into a simple drawer pull-out
- Epoxy and E-coat finish is durable
- Ecoated steel suits coastal and wet climates
Cons
- Tie-down system sold separately
- Does not fit Zero-series fridges
- Residual rattle needs adjustment
The ARB 10900021 is a purpose-built drawer-type slide for the Classic Series I and II 37 and 50 quart fridges. The tray measures 26 by 16 in and the rated maximum weight capacity is 175 lb, which is a sensible ceiling for the fridges it was designed around. At 27.6 lb the slide is also one of the lighter options here, and that matters in a half-ton bed.
If you already own an ARB Classic Series fridge, this is close to a no-brainer. The fit is designed rather than universal, the epoxy or E-coat finish is a genuinely good corrosion choice, and owners with long-running installs report it still working years later. Reviewers describe the bearings as slick even with the fridge fully loaded.
Plan on one extra purchase, because the ARB tie-down system, part number 10900010, is sold separately, so budget for it or bring your own retention. This slide will not fit ARB Zero models at all.
Retention Is Not Included, So Add It
Without a tie-down, the fridge sits in the tray on its own feet and can shift during cornering or braking. The ARB tie-down kit is the cleanest fix because it is designed to interface with this tray. If you would rather not buy a second part, a pair of heavy straps across the lid handles are the usual substitute.
Residual rattle is the other recurring comment. Owners generally resolve it with a small adjustment to the slide feet rather than by replacing hardware, so budget an evening rather than a repair.
When This One Is the Wrong Buy
Skip it if your fridge is a Zero-series ARB, since the Zero units use a different tray. It is also the wrong choice if you want a universal slide you can move between trucks, because the model-specific fit is the whole point and also the whole limitation.
Value it honestly as a brand-fit purchase rather than a specification winner. A 175 lb rating in a 26 by 16 in tray is less generous than the universal slides here, and you are paying partly for the ARB name and the exact fit.
4. ALL-TOP ATFS-30a Fridge Slide – Budget Pick for 35L to 40L Fridges
ALL-TOP Fridge Slide (Inner 29.3 x 18.7in) Vehicle Refrigerator Freezer Slider with 4 Buckle Straps, Universal Fit, Max 287 LBS, 3rd Gen
Rated to 285 lb / 130 kg
Inner tray 29.3 x 18.7 in
Cold-rolled steel, galvanized and powder coated
Three-year warranty
Pros
- 285 lb rating far above what a 40L fridge needs
- Galvanized cold-rolled steel under a thick powder coat
- Two-hand operate handles for safe control
- Four buckle straps and stainless hardware in the box
- Also used for toolboxes and generators
Cons
- Occasional ball-bearing shedding and broken extension stop clips
- Some units had straps missing or welds needing filing
- Inner tray sits just under an inch above the mounting surface
The ALL-TOP ATFS-30a is the budget entry that punches above its weight. The inner tray is 29.3 by 18.7 in, the industrial bearing slide rails are rated to 285 lb, and the construction is cold-rolled steel with a galvanized treatment under a thick powder coat. The rails are full extension with two-hand operate handles, so you can control a loaded tray without pinching your fingers.
For a 35L to 40L portable fridge, including Engel and EcoFlow units in that range, the fit works well and the rating leaves plenty of margin. Installation is screw-in with the supplied stainless screw and bolt set, and the four buckle straps are included. Owners also report using the tray for toolboxes and other heavy cargo, which is again what the frame is designed to handle.
The quality control is the weak point, and it is worth being direct about. A minority of buyers report ball bearings shedding, the plastic extension stop clip arriving cracked, missing straps in the box, and weld finishing that burned through the tray and needed filing and repainting before mounting. None of that is a structural failure of the design; it is a consistency problem at this price tier.
The Clearance Problem With Low-Profile Trays
The inner tray sits just under an inch above the mounting surface, which is a genuine advantage when you are fighting for vertical clearance under a tonneau cover. It is also the reason the owners who need a tall fridge sometimes have to build a riser underneath the whole unit.
That trade is usually worth it on a truck with a hard cover, and it is a poor trade on a truck with plenty of headroom. Measure your closed height, add the fridge height, and only then decide whether the low profile helps or hurts you.
Inspect the Box Before You Mount It
Because the failure mode here is assembly consistency rather than design, spend five minutes at unboxing. Run the tray in and out on the floor, confirm the ball bearings roll freely, check the extension stop clips are intact, and verify the straps are actually in the box.
Check the welds with a flashlight along the tray seams and file any burn-through before the powder coat gets loaded with mud. The three-year warranty gives you a route if something fails early, which is a meaningful difference versus cheaper unbranded trays with no support path.
5. SAMOUT SMFS-30 Fridge Slide – Top Rated Universal Slide With a Real Lock
SAMOUT Fridge Slide (Inner 29.2 x 18.7in) Vehicle Refrigerator Freezer Slider with 4 Buckle Straps, Universal Fit, Max 287 LBS, 3rd Gen
Rated to 285 lb / 130 kg
Inner tray 29.2 x 18.7 in
Overall 30.8 x 20.5 x 2.3 in
Three-year warranty
Pros
- Slides lock positively in both open and closed positions via blue release tabs
- No rattle with a loaded fridge once fitted
- Reasonable price against premium-brand slides
- Holds up over washboard and dirt roads
- Mounts ARB 12V fridges without modification
Cons
- Supplied tie-down straps are awkward
- roughly 5 in wider than some small coolers
- Double locks need deliberate action to release
The SAMOUT SMFS-30 is the one we would recommend to someone who asked for a single slide with no compromises in the middle. It has a 29.2 by 18.7 in inner tray, 285 lb slide rails, full extension and two-hand operate handles, and the construction is the same cold-rolled steel with galvanized treatment under a thick powder coat you see on the budget tier.
What separates it is retention. The slides lock positively in both the open and closed positions using blue release tabs, which directly addresses the complaint owners raise about extended slides rolling shut on an incline. That is not a cosmetic feature. A runaway tray on a grade can close on your hand or on the fridge lid, and a positive lock is the difference between a controlled drawer and a hazard.
Owners report no rattle with a loaded fridge, smooth operation, and durability over months of washboard and dirt road use in a campervan. One of them fitted it to an ARB 12V fridge with no modification, which tells you how genuinely universal this tray is despite being sold as a universal slide rather than a brand-fit part.
The two criticisms are small but real. The supplied buckle straps are awkward to fit and many owners replace them with velcro straps, and the tray is around 5 in wider than some smaller coolers, so a compact fridge will sit with visible play around it.
Why the Lock Matters More Than Most Buyers Expect
Parking sites are not level. On any slope, an unlocked extended tray wants to roll closed, and a loaded fridge makes it heavy enough to do real damage to a hand, an arm or a fridge hinge. Positive lock tabs in both positions are the feature we value highest on this list, and few competing slides manage it.
The blue release tabs do need deliberate pressure, which some owners find slightly awkward during daily use. In exchange you get a tray that stays exactly where you put it, which is worth the extra second every time.
Swapping the Supplied Straps
Most of the negative feedback on this slide comes down to the buckle straps that ship in the box. A set of velcro straps costs a few dollars, fits far more fridge lid shapes, and takes seconds to swap. It is the first modification we would make to this tray.
Because the slide is roughly 5 in wider than a small cooler, add a foam or rubber anti-slip pad under the fridge so it does not rock inside the tray. That converts the extra width from a problem into harmless margin.
6. Dometic CFX3 50/55/65 Slide Mount Kit – Best for Dometic CFX3 Fridges
DOMETIC Slide for CFX3 55-Liter Portable Refrigerator and Freezer with Ice Maker
Slide mount kit for CFX3 50/55/65
Side-mount drawer type
43 lb unit weight
Plenty of pre-drilled mounting holes
Pros
- Feels heavy duty and substantial once mounted
- Plenty of pre-drilled holes and can be drilled for custom fit
- Fridge can mount with screws from below and straps
- Proven in teardrop trailers
- trucks and plywood camper builds
Cons
- Assembly uses pop rivets rather than welds and rivets can loosen
- One owner reported plastic components breaking after about two years
- Build quality lags the welded trays in this group
The Dometic slide mount kit covers the CFX3 50, 55 and 65 litre fridges, which covers a huge share of the portable fridge market. It is a side-mount design in a brushed finish, and at 43 lb it is heavy in a way that tells you something about the steel in the frame. Positive reviews consistently describe it as feeling heavy duty and substantial once mounted.
The mounting flexibility is the genuine strength. There are plenty of pre-drilled holes, and it can be drilled further for a custom fit, and the fridge can be secured with screws from below and straps at the same time. Owners use it in teardrop trailers, in truck beds and in plywood camper builds, which is a fairly broad endorsement for a single kit.
Its 3.9 rating is the lowest in this roundup, and the reasons are specific enough to describe. The construction uses pop rivets rather than welds, and those rivets can loosen or pop out in transit. One owner reported the unit shattering after about two years, with plastic components breaking on extension. And several buyers felt the cost was hard to justify for a simple steel slide tray.
Rivet Joints Need Inspection
If you buy this, check every rivet after the first month of driving, and again after any long trip on rough roads. A rattle that appears out of nowhere is usually a rivet working loose, and it is a five-minute fix with a rivet gun if you catch it early.
Warranty handling is another friction point. Dometic directs buyers to contact the company directly for coverage rather than handling it through the retail listing, so keep your order details somewhere you can find them from a phone.
Who Should Look Past This One
If your CFX3 is a 95 dual-zone, the tray is too narrow and you need something else entirely. If you are on a rough road, run serious wheel travel, or plan to keep the build for many seasons, the riveted assembly is a fair reason to look at a welded alternative with a similar footprint.
Where it does make sense is a CFX3 50, 55 or 65 on relatively mild roads, where the pre-drilled hole pattern saves you a lot of layout work. The fit convenience is real, and the price is a secondary consideration next to mounting to the exact hole pattern of the fridge you already own.
7. ARB 10900040 Elements 63QT Slide – Best for ARB Elements 63-Quart
ARB 10900040 Fridge Freezer Slide Exclusively for ARB 10810602 Elements 63QT Weatherproof Ideal to gain Access to Food and Drinks
Sealed roller bearings with lock-in lock-out
Zinc plated with black epoxy E-coat
879 x 525 mm tray
38 lb unit weight
Pros
- Overbuilt construction with a release lever that works from either side
- Holds the fridge securely with very little movement
- Laser-cut drain hole empties the fridge without lifting it out
- Can be permanently mounted through the base holes
Cons
- Model-specific to the ARB Elements 63-quart fridge
- 38 lb unit weight is heavy for a half-ton bed
- A separate ARB tie-down kit is advisable off-road
The ARB 10900040 is built for the ARB Elements 63-quart fridge, and it is one of the most thoughtfully engineered slides in this group. The closed dimensions are 884 by 579 by 79 mm, it extends 688 mm for a total of 1573 mm, and the tray itself is 879 by 525 by 47 mm. The whole thing is 34.8 in long, 22.8 in wide and 3.11 in thick.
Three details set it apart. Sealed roller bearings with a lock-in, lock-out mechanism mean the tray stays where you leave it, which is the extended-position safety issue we keep coming back to. New fridge feet retainers hold the unit rather than letting it slide on its own feet. And a laser-cut hole in the mounting plate lets fluid drain from the fridge without lifting it out of the slide.
The finish is zinc plated with a black epoxy E-coat, which is a good choice if you camp near the coast or in winter conditions, and the base has holes for permanent mounting. Owners report that it holds the fridge very securely even off-road, and one has fitted it to a Dometic CFX75DZ as well as the intended ARB unit.
What the Drain Hole Actually Solves
Without a drain path, melted ice and condensation sit in the tray and end up on the bed floor or in a plywood camper box. The laser-cut hole in the mounting plate means you can tip the fridge and let it drain with the tray still in place, which saves a lot of awkward lifting.
It is a small design decision that tells you how the rest of the product was thought through. If your use case involves a lot of cold drinks and long hot days, that is worth more than a slightly higher price tag.
Fitment Is the Trade-Off
This slide is for the ARB Elements 63-quart model, and while one owner has made it work with a Dometic CFX75DZ, that is an adaptation rather than a supported fit. If your fridge is a different brand, treat this as a no-go and look at one of the universal trays instead.
At 38 lb it is also heavy, and half-ton owners should add it to the payload calculation along with the fridge. Buying the optional ARB tie-down kit is the other thing we would do here, because off-road, a slide that holds securely and a fridge that cannot jump out are both worth paying for.
8. ICECO JP Pro Series Slide Mount – Best for ICECO JP Pro Fridges
ICECO Slide Mount for JP Pro Series Portable Refrigerator Freezer, Car Fridge Freezer Slide (Slide for JP30 Pro/JP40 Pro/JP50 Pro)
Fits JP30 Pro, JP40 Pro and JP50 Pro
27.5 x 17.5 x 2.1 in
Three-position locking mechanism
Two-year warranty
Pros
- Works and locks adequately as an entry-level slide for JP Pro fridges
- Reasonable price against OEM-brand slides
- Handles a 40-quart fridge when properly installed
Cons
- Thin-gauge metal that bends and flexes off-road
- Bolts and screws often arrive loose or missing
- About an inch of play in the locked position
- Plastic end bumpers crack and no replacement parts are sold
The ICECO slide mount covers the JP30 Pro, JP40 Pro and JP50 Pro portable fridges. The footprint is 27.5 in deep by 17.5 in wide by 2.1 in tall, with a three-position locking mechanism and heavy duty steel construction with durable slide rails. At that footprint it is one of the smaller trays here, and it suits the ICECO range well.
Its 4.0 rating is the second lowest here, and the build quality is the weakest. Owners report thin-gauge metal that bends and flexes under off-road use, bolts and screws that frequently arrive loose or missing, a bent latch rod, and up to an inch of play in the locked position that bounces over rough ground.
The plastic end bumpers are the detail that annoys people most. They deteriorate and shatter after roughly a year, and the manufacturer does not sell replacements, so once they go you are looking at exposed runners. The warranty is two years, which is shorter than the three years on the comparable universal slides.
It can still be the right answer in one specific case. If you own a JP Pro fridge, want the exact model fit, and drive on paved roads with the occasional forest track, it locks adequately and it is priced reasonably against OEM-brand slides.
Reinforce It or Replace It
If you fit this slide, add a cross brace between the tray frame and the bed floor. Thin-gauge flex is the core complaint, and a simple brace or a length of angle under the tray converts it from a nuisance into a usable install for a moderate amount of work.
Tighten every bolt at installation and re-torque them after the first hundred miles, because the loose-hardware feedback is common enough that it should be treated as a setup step rather than bad luck. A thread-locking compound on the slide bolts is worth using.
Watch Your Tailgate Clearance
Several owners note the tray may need extra elevation to clear an angled truck bed tailgate or a tonneau cover. At 2.1 in of thickness the slide itself is slim, so the geometry problem is usually the fridge sitting higher than expected, not the tray.
If your bed is tight, measure the closed height with the fridge in place before ordering. A slide that needs a wooden riser to fit is a worse buy than a slightly taller slide that fits flat, and this is the one area where the ICECO unit needs the most care.
9. ARB 10900048 Zero 63/73QT Slide – Best for ARB Zero Fridges
ARB 10900048 Fridge Slide for Fridge Model Zero 63Qt/73Qt, Solution to gain Access to Food and Drinks
Sealed roller bearings with lock-in lock-out
930 x 404 mm tray
Zinc plated with black epoxy E-coat
37.24 x 17.48 x 3.11 in closed
Pros
- Premium ARB build quality and tested durability
- Smooth full extension with a secure multi-position latch
- Fridge feet retainers hold the Zero-series unit firmly
- Drainage hole in the mounting plate
- Closed footprint is narrow enough for a tight bed
Cons
- Only fits the ARB Zero 63 and 73-quart fridges
- Model-specific tray with no universal alternative
The ARB 10900048 is the dedicated slide for the ARB Zero 63 and 73 quart fridges. Its closed dimensions are 946 mm long by 444 mm wide by 79 mm tall, extending 723 mm for a total of 1669 mm, with a 930 by 404 mm tray. In inches that is 37.24 by 17.48 by 3.11 in closed, and it is the narrowest closed profile of the ARB slides here.
The engineering is the same high standard as the Elements slide. Sealed roller bearings with a lock-in, lock-out mechanism, new fridge feet retainers, holes in the base for permanent mounting, zinc plating under a black epoxy E-coat, and a laser-cut drainage hole in the mounting plate. The tray walls act as end stops against fore-aft movement, which is the tray-length complaint that shows up with more generic slides.
Owners of the Zero fridges describe comfortable access, easier organisation and cleaning, and a lock that holds on rough angles. The narrow closed width is genuinely useful in a bed where a wider slide would eat the space you need for getting behind it.
The trade-offs are fitment and weight commitment. It is a tray built to do one job for one fridge family. If you are still choosing which fridge to buy, a universal slide gives you far more freedom than committing to a model-specific tray.
When the Narrow Closed Width Helps
A 444 mm closed width leaves a meaningful strip of bed alongside the slide, which matters when you still want to load long items past the fridge. On a short bed with a tailgate that opens across the full width, every spare inch of bed floor is space you can actually use.
It also clears hard covers more easily than a wide tray, because the closed profile is only 79 mm tall. Measure under your tonneau cover and this becomes the slide most likely to fit without building a riser.
Is a Model-Specific Slide Worth It?
Buy one when you already own a Zero 63 or 73 quart fridge. The perfect fit, the feet retainers and the lock are things a universal tray cannot fully replicate, and the drain hole is a nice touch on a fridge that spends its life full of condensation.
Pass if you are still shopping for the fridge. The same money in a universal slide plus a wider tray will serve you across brands and across future fridge upgrades, and for most builds that flexibility is worth more than the last inch of retention security.
10. SetPower Universal Refrigerator Slide Mount – Best for SetPower Fridges
SetPower Universal Refrigerator Slide Mount – Compatible with SetPower Portable Refrigerator Car Fridges (Excludes AJ & AB Series), Electric Cooler Slide for Truck, SUV, Vans
Rated to 200 kg / 440 lb
Three locking positions
Four tie-down straps included
29.1 lb unit weight
Pros
- Smooth one-hand operation from a single centre lever
- Three lock positions including fully extended
- Owners report no rattling and a sturdy feel
- Includes four fixing straps and fits SetPower units with wheels
- Extends access for shorter users who cannot reach into a raised bed
Cons
- No mounting hardware included
- so you pick the fixings
- Extended tray can be noisy over washboard roads
The SetPower slide mount is built around oxide-coated heavy-duty steel described as waterproof, rust and corrosion resistant, and it carries a 200 kg, or 440 lb, rating, which is the highest figure in this roundup. It weighs 29.1 lb, so it is a reasonably heavy tray that still does not dominate your payload.
The mechanism is the story. A single centre lever operable with one hand moves the slide between three locking positions: closed, halfway and fully extended. Owners report smooth motion, a sturdy feel and no rattling once the fridge is loaded, which is not something every tray at this level manages.
It is also the one here that explicitly solves a reach problem. Several buyers fitted it so a shorter user or someone with limited mobility could get at the fridge without climbing into a raised bed, which is a genuinely useful reason to buy a slide beyond convenience.
It fits most SetPower portable fridges, including units with wheels attached, and excludes the AJ and AB series along with the RF30 and PT30. Four polypropylene fibre fixing straps are included, and compatible variants cover other SetPower models.
Two drawbacks recur. Mounting hardware is not included, so you choose the bolts based on your own bed and liner. The extended tray can also be noisy over washboard roads with the fridge out.
Plan Your Own Hardware
No mounting hardware means you are choosing between bolt-through, rivnut or E-track based on your own setup, which is a benefit as much as an inconvenience. Pick bolts and washers appropriate to a bed liner, and seal every hole if you camp in wet or salty conditions.
Because the rating is high and the frame is heavy, use a bed with a payload figure that comfortably absorbs a 29 lb slide plus a loaded fridge plus a battery. The margin is what keeps the setup stable when the washboard roads start.
Three Lock Positions Are More Useful Than They Sound
The halfway position is the one people end up using most. It is far enough out to reach food and drinks without the tray projecting into the tailgate, and close enough in that the centre of gravity stays over the bed floor. A single-slide tray with only open and closed options does not give you that middle ground.
If you also want the access angle without hauling the tray all the way out, the middle detent is a small quality-of-life feature that adds up across a long trip. Combine it with velcro straps instead of the supplied ones if the fridge lid shape fights you.
How to Measure Your Truck Bed for a Fridge Slide
Measurement is where installs go wrong most often, and it takes ten minutes with a tape measure. Work through these five items before you buy anything, and you will avoid the clearance problems that come up repeatedly in this category.
Measure the available length. From the tailgate to the toolbox or bed wall, then subtract the tray length plus the fridge depth plus two inches of working room. A tray that fits only when the fridge is pushed hard against the front stop is a tray that rattles on corrugations.
Measure closed height, not open height. With the tonneau cover fully closed, measure from the bed floor to the lowest point of the cover or the toolbox. Then add the slide thickness and the fridge height. Slide thicknesses on this list run from about 2.1 in to 3.5 in, so that addition is not trivial.
Measure the height when the tailgate is open. An angled tailgate can cut into the rear of the tray. Several owners discovered this only after the slide was bolted down, so check the geometry before the drill goes near the bed floor.
Check the inner tray against the fridge footprint. Compare your fridge width and depth against the inner tray dimensions, not the external ones. Wall thickness and side rails mean the usable surface is always smaller than the numbers on the box.
Check the payload sticker. The number on the door jamb is the remaining capacity for passengers, cargo and all modifications. Add the slide weight first, then the loaded fridge, then batteries, then gear.
If you also carry a motorcycle, a bike or heavy recovery gear in the same bed, do the loading maths properly before you commit to a tray. Our pick of motorcycle ramps for truck loading covers the weight side of that calculation.
Horizontal vs Tilt vs Side-Pull: Which Slide Type Do You Need?
Almost every slide on the market is a horizontal pull-out tray, including all ten in this roundup. That is by design. A horizontal tray is the simplest, lowest and most dependable approach, and it is what you should buy unless a specific problem calls for something else.
Horizontal pull-out. The fridge sits flat and slides toward the tailgate. It keeps the closed height and the mechanism simple, and it is the type most people should start with.
Tilt slide. The tray hinges or tips so the fridge leans back toward you, presenting the open lid at a more natural angle. The appeal is real for tall fridges and for anyone who finds bending over a flat tray uncomfortable. The drawbacks are just as real: the mechanism adds weight, raises the closed height, introduces a pivot point that can work loose, and there are very few on the market to choose from. Tilt slides are legitimate, but they are a niche answer to a comfort problem that a lower tray or a cutting board also solves.
Side-pull and swing-away. The tray moves sideways or swings out from under the fridge. Useful in a campervan or a narrow drawer where front access is blocked, but in an open truck bed you lose the rear access that matters most, so it is rarely the right answer for this application.
Double-stack and vertical systems. These put a second fridge above or beside the first, or add a cutting board and storage above the tray. They solve payload stacking rather than access, they are heavy, and they cost considerably more. Worth a look only if you have already run out of bed floor.
Our advice: buy a horizontal slide with a positive lock, secure the fridge with straps, and only consider a tilt if you have actually used a flat tray and found the angle genuinely difficult. Most of the time the tilt question answers itself once the cutting board goes on.
Load Rating, Fridge Weight and Truck Payload
A load rating is the maximum weight the slide rails are rated to carry, evenly loaded. It is not a recommendation and it is not the same as the weight of your fridge. The rating exists so the rails do not deform or the bearings do not fail under sustained load, and overloading a slide produces exactly the rattle and slop that owners complain about.
Work out your real figure before you buy. Take the empty weight of your fridge, add the weight of a full load of food and drinks, and compare the total to the slide rating. Then add the slide’s own weight to that total, because both of those numbers come out of the same truck payload allowance.
Here is the range on this list. The ARB 37/50 quart slide is rated to 175 lb, which is the tightest ceiling and pairs with a small fridge. The Rough Country tray claims up to 250 lb. The ALL-TOP and SAMOUT slides are rated to 285 lb, the SetPower mount to 440 lb, and the MORryde to 225 lb. A loaded 50L fridge is usually well inside all of those figures, so the rating rarely decides the purchase on its own.
What does decide the purchase is the tray footprint and the retained position. A tray with a 175 lb rating and inner walls that grip the fridge is safer and quieter than a 285 lb tray the fridge can slide around inside, because movement is what causes both noise and fatigue in the runners.
The payload conversation matters more than most buyers expect. A 68 lb slide, a loaded 50L fridge and a lithium battery can quietly consume a large share of what a half-ton truck has left for passengers and gear. The number on your door jamb sticker is a limit, not a target, and running past it changes how the truck handles before anything fails.
Finally, the safety point that almost no retailer mentions. A slide with no positive lock in the extended position can roll shut on any incline, and a loaded tray carries enough momentum to pinch a hand or crush a fridge lid. Where a slide offers lock-in, lock-out or multi-position detents, treat that as a safety feature and not a convenience feature.
Frequently Asked Questions
Which fridge slide is the best?
The MORryde SP56-115 is the best all-round fridge slide for truck beds in our testing, with a 225 lb load rating, 200 percent extension runners and dual travel latches. Choose the Rough Country 99021 for the best value with included straps, the SAMOUT SMFS-30 for a positive lock in both open and closed positions, or a model-specific ARB or Dometic slide if you already own a fridge from those brands.
Is a fridge slide worth it?
Yes, for most truck campers, overlanders, hunters and tailgaters, because it turns a fridge you have to climb into a packed bed for into one you can reach from the tailgate. It is not worth it in a very short bed where the fridge lifts out easily, or where the slide steals flat space you need for cargo. Remember the slide weight and fridge weight both come out of the same payload allowance.
Are tilt fridge slides any good?
Tilt slides are legitimate but niche. Tilting the tray presents the open lid at a more comfortable angle, which helps with tall fridges. The mechanism adds weight, raises closed height for tonneau clearance, and introduces a pivot that can work loose. Most buyers are better served by a low-profile horizontal slide with full extension, which is what all ten picks in this roundup are.
How much weight can a fridge slide hold?
Ratings in this category run from 175 lb on the ARB 37/50 quart slide up to 440 lb on the SetPower universal mount, with most universal steel trays rated between 225 and 285 lb. Check that your fridge plus a full load of food stays under the rating, and that the combined weight of slide, fridge and battery stays under your truck’s payload figure.
Will a fridge slide fit under my tonneau cover?
Often, but you have to measure. Close the cover fully and measure from the bed floor to its lowest point, then add the slide thickness and the fridge height. Slide heights range from about 2.1 in to 3.5 in, so a low-profile tray is often the difference between clearing the cover and building a riser. Also check that an angled tailgate does not cut into the rear of the tray.
Do fridge slides rust in salt and mud?
It depends entirely on the finish. Budget trays use galvanized cold-rolled steel under powder coating, which is adequate but can chip at welds and scratch. Premium slides use zinc plating with a black epoxy E-coat or heavier steel, which resists corrosion far better. Rinse slides with fresh water after coastal trips and touch up any chips in the coating promptly.
Which Fridge Slide Should You Buy?
The best fridge slides for truck beds come down to two decisions. If you want one recommendation and you are starting from a generic 40L to 50L fridge, take the MORryde SP56-115, because the 225 lb rating and 200 percent extension solve the access problem cleanly and the 31.42 in inner tray fits most mid-size units.
Buy the Rough Country 99021 instead if you want the most complete install in the box, since the straps, hardware and nutserts are already included and the 250 lb rating is generous. Buy the SAMOUT SMFS-30 if the extended-position lock is what worries you most, and swap the supplied straps for velcro ones while you are at it.
If you already own a specific fridge, the model-specific slides are the better buy. The ARB 10900021 fits Classic Series 37 and 50 quart units, the ARB 10900040 fits the Elements 63-quart, the ARB 10900048 fits the Zero 63 and 73 quart, and the Dometic kit covers the CFX3 50, 55 and 65.
Before any of them goes in the bed, measure your closed clearance under the cover, check the inner tray against the fridge footprint, and add the slide weight to your payload maths. Ten minutes with a tape measure is the difference between an install that takes an afternoon and one that goes in the wrong hole.